Champaign, Illinois(217) 398-8970, Ext [email protected] THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
10HOW TO CUT COVERING FROM BALSAUse a soldering iron to cut the covering from the stab. The tip of the soldering iron doesn’t have to be sharp, but a
11Install the Rudder❏ 1. Install three hinges into the rudder using the same techniques used on the ailerons and elevators and then install the rudder
12❏ 3. Apply thread locker to the 4-40 set screw and then install it into the 3/32" [2 mm] wheel collar. Slide the wheel collar onto the tail wir
13❏ 2. Install one half of a 2" [51mm ] piece of adhesive backed Velcro® to the bottom of the motor box and the other half to the bottom of the E
14screw into each of the holes you have drilled. Apply a drop of thin CA into the holes to harden the threads. Once the glue has cured secure the cont
15❏ 2. Locate the 2-56 wire with threads at both ends, two #2 fl at washers and #2 nuts.❏ 3. Insert the wire into the hole in the bottom of the rudder.
16the rudder torque rod horn. Drop the string through the slot in the fuselage, feeding it through the fuselage to the rudder servo. Do this for both
17❏ 3. Install the spinner back plate onto the motor shaft. Enlarge the hole in the back plate as needed to fi t your brand of motor. Remove the spinne
18Up & DownThese are the recommended control surface throws:3/8"[10 mm]7°1-1/4"[32mm]12°3/8"[16 mm]9°ELEVATORAILERONLOWRUDDERUp &am
19❏ 2. With the wing attached to the fuselage, all parts of the model installed (ready to fl y) and LiPo battery, lift it at the balance point you mark
2INTRODUCTIONThe full scale Extra 300SP is the choice of many airshow performers. The Extra 300SP is known for its tremendous power and ability to per
20Range CheckGround check the operational range of your radio before the fi rst fl ight of the day. With the transmitter antenna collapsed and the recei
21CHECK LISTDuring the last few moments of preparation your mind may be elsewhere anticipating the excitement of the fi rst fl ight. Because of this, yo
22FlightFor reassurance and to keep an eye on other air traffi c, it is a good idea to have an assistant on the fl ight line with you. Tell him to remin
23This model belongs to:NameAddressCity, State, ZipPhone NumberAMA Number
GPMA1188Entire Contents © 2014 Great Planes Model Mfg. A subsidiary of Hobbico, Inc.
32. You must assemble the model according to the instructions. Do not alter or modify the model, as doing so may result in an unsafe or unfl yable mode
4will also be required to power the receiver. Be sure to follow the ESC instructions for using a separate power source (voltage regulator or receiver
5ORDERING REPLACEMENT PARTSReplacement parts for the Great Planes Extra 300SP EP ARF are available using the order numbers in the Replacement Parts Li
6PREPARATIONS❏ 1. If you have not done so already, remove the major parts of the kit from the box and inspect for damage. If any parts are damaged or
7❏ ❏ 6. Remove the fl at nylon mounting plate from the clevis. The fl at plate can be discarded.❏ ❏ 7. Using a felt tip marker, draw a line from the ser
8ASSEMBLE THE FUSELAGENote: If you have not already fi gured out how to remove the canopy, the magnets at the rear of the canopy keep it locked in plac
9❏ ❏ 4. Install the wheel pants to the landing gear using two 2-56 3/8" [10 mm] machine screws, #2 lock washers and #2 fl at washers. Apply a d
Commentaires sur ces manuels