Great-planes PT-19 EP ARF - GPMA1149 Manuel d'utilisateur

Champaign, Illinois(217) 398-8970, Ext [email protected] Contents © Copyright 2009 GPMA1149 MnlREAD THROUGH THIS MANUAL BEFORE STARTIN

10INSTALL THE TAILInstall the HorizontalStabilizer & Elevators❏ 1. Temporarily fi t the wing to the fuselage using two 3mm x 25mm machine screws an

11❏ 8. Prepare four hinges using T-pins as shown. Insert the T-pin through the center of each hinge. Fit a hinge to each hinge slot in the elevator. T

12❏ 5. Fit the tailwheel assembly to the rudder by sliding the guide wire into the pre-drilled hole in the rudder. Do not glue it in place at this tim

13❏ 3. Epoxy the servo mounting plate to the servo tray. Screw the elevator servo in position so that the output shaft of the servo is oriented forwar

14❏ 7. With your servo centered, fi t the standard size servo arm to your servo so that the servo arm is 90° to the pushrod. Use a #55 [1.3mm] drill to

15INSTALL THE MOTOR, ESC,RECEIVER, & BATTERY❏ 1. Remove the three backplate screws, the brass collar set screw, and apply thread locking compound

16❏ 7. Prepare the surface and attach the remaining adhesive backed hook-and-loop material (hook side) to the battery tray in the location shown. Stic

17❏ 2. Connect the aileron servo lead to the receiver. If you are using a 2.4GHz radio, arrange your receiver’s antennas as directed by the radio manu

18❏ 8. Using some scrap balsa, cut four short strips to make fl anges to help join the left and right pieces. Glue two fl anges to one half using thin C

19❏ 2. Position your pilot(s) where you want them. Remove the hatch. Glue the 45mm x 15mm piece of balsa sheet in the front cockpit as shown if you wi

2TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2AMA . . . . . . . . . . . . . . . . . . . . . . . . .

20for which it was intended. DO NOT OVERLOOK THESE IMPORTANT PROCEDURES. A model that is not properly setup may be unstable and possibly unfl yable.The

21❏ 4. If the tail drops, the model is “tail heavy” and the battery pack must be shifted forward or weight must be added to the nose to balance. If th

22MOTOR SAFETY PRECAUTIONSFailure to follow these safety precautions may result in severe injury to yourself and others.Get help from an experienced p

23❏ 9. Pull / push on each of the pushrods and check to see that the adjustable pushrod connectors do not slip.❏ 10. Check the servo arms for secure a

24but to hold the turn you’ll need rudder and a little opposite aileron to keep your bank angle. Try transitioning from left to right and making turns

32. You must assemble the model according to the instructions. Do not alter or modify the model, as doing so may result in an unsafe or unfl yable mode

4❍ Great Planes 10x4.5 PowerFlow™ Propeller (GPMQ6660) (draws 15 amps max.)❍ Great Planes 3.5mm Male/2.5mm Female Bullet Connector Adapter (GPMM3122

5● Whenever the term glue is written you should rely upon your experience to decide what type of glue to use. When a specifi c type of adhesive works

6ORDERING REPLACEMENT PARTSReplacement parts for the Great Planes PT-19 EP ARF are available using the order numbers in the Replacement Parts List tha

7so that one overlies the other. You now have a single 5mm thick wing joiner.❏ 3. Coat both faces of the wing joiner with 30-minute epoxy and fi t the

8❏ 3. Remove the servo arm from the servo. Install your aileron servo so that the output shaft is oriented forward. Route the lead through the mountin

9❏ 9. Fit the Z-bend of a 1mm x 80mm pushrod into the hole of each torque rod horn. With the servo still centered, slide the screw-lock pushrod connec